Course Content
Introduction to SolidWorks
-
Launching SW and touring the interface
02:16 -
The 3D logic and starting a sketch
05:51
Sketch Tools
-
Sketch tools Lines
03:05 -
Sketch tools rectangles
03:59 -
Sketch tools circles
01:51 -
Sketch tools slots
03:28 -
Sketch tools Arcs
02:52 -
Sketch tools Polygons
01:33 -
Sketch tools Ellipse
01:21 -
Sketch Blocks
06:54 -
Blocks and kinematics
07:54 -
Kinematics Practice
08:58 -
Auto Trace
05:39 -
Over Defined Sketches
08:05
Sketch Editing Tools
-
Dimensioning
03:40 -
11/ Fillet and chamfer
03:49 -
SM Practice 2 (3)
18:35 -
Offset
02:37 -
Mirror and Patterns
05:55 -
Power trim and extend
04:07 -
Constraints and DOFS
12:44 -
Mechanism simulation 1
02:46 -
Mechanism simulation 2
03:42
Sketch Practice
-
Sketch Exercise 1
07:54 -
Sketch Exercise 2
05:48 -
Sketch Exercise 3
06:57 -
Sketch Exercise 4
02:56 -
Sketch Exercise 5
06:33 -
Sketch Exercise 6
06:36 -
Sketch Exercise 7
04:07 -
Sketch Exercise 8
04:15 -
Sketch Exercise 9
06:24 -
Sketch Exercise 10
06:59 -
Sketch Exercise 11
14:20 -
Sketch Exercise 12
07:43
Solid Modeling Features
-
Extrude 1
08:42 -
Extrude 2
15:17 -
Extrude Practice 1
06:04 -
Extrude Practice 2
06:21 -
Extrude Practice 3
05:58 -
Extrude Practice 4
06:37 -
Extrude Practice 5
08:51 -
Revolve
08:21 -
Revolve Exercise 1
06:01 -
Revolve Exercise 2
13:24 -
Swept boss cut
07:45 -
Swept Boss Exercise 1
02:46 -
Swept Boss Exercise 2
10:39 -
Creating Planes
07:04 -
Loft
05:12 -
Loft 2
07:20 -
Spline
03:07 -
Bottle Exercise
06:33 -
Reducer Exercise
11:06
Solid Modeling Editing Features
-
Chamfer and Fillet
08:07 -
Rib
05:20 -
Shell
04:55 -
Draft
05:11 -
Wrap
05:45 -
Rib Exercise
04:43 -
Spline Loft Exercise
09:32 -
Hole Wizard
07:33 -
Multi Body
07:11 -
Linear and Circular Pattern
19:18 -
Other Patterns
12:58 -
Mirror
04:09 -
Bulb Shell
07:41 -
Multi Body Practice
14:01 -
Button Practice
07:48
3D Sketch
-
3D Sketch
06:08 -
3D Sketch Exercise
04:34
Solid Modeling Practice
-
General Practice
14:31 -
General Practice 2
15:45 -
Hook Practice
19:58 -
General Practice 3
19:59 -
Measure tool
09:45 -
Surface basics
07:56 -
Surface Practice
11:58
Sheet Metal Modeling
-
Sheet Metal Base and Edge Flange
12:56 -
Hem
04:07 -
Sketched Bend
03:42 -
Tab and Jog
07:03 -
Miter Flange
04:20 -
Closed Corner
04:03 -
Gusset and Flatten
08:04 -
Corner Relief
05:04 -
Fold and unfold
02:43 -
Simple Hole and Extruded Cut
02:59 -
Tab and Slot
08:10 -
Forming Tool
06:33 -
Lofted bend
04:15 -
The K Factor
09:13 -
SM Practice 1
15:56 -
SM Practice 2 Part One
17:58 -
SM practice 2 Part Two
15:15 -
SM Practice 2 Part Three
18:34 -
Sheet Metal Practice 3
12:34 -
Sheet Metal Practice 4
19:56
SolidWorks Weldments
-
Placing Frames
06:08 -
Structural Members and Grouping
14:28 -
Trim Extend
10:47 -
Cap End Gusset and Weld Bead
15:26 -
Defining Profiles and The Cut list
09:27 -
Weldments Practice 1
06:37 -
Weldments Practice 2
18:25
BONUS Project / Concept Design
-
Introduction and Defining Variables
02:56 -
Creating the Main Sketch
03:57 -
Placing The Frames
02:26 -
Patterning The Side
01:35 -
Defining The Purlins Profile
05:11 -
Placing The Purlins
04:54
BONUS Project / Design Verification by FEA
-
Defining A Material And Accessing The Analysis
01:42 -
Preparing The Model For The Analysis
02:36 -
Defining Fixtures and loads Then Running the Analysis
04:19
BONUS Project / Model Enhancing
-
Modifying The Model For Enhanced Analysis Results
05:08 -
Rerun The Analysis With Some Enhancements
05:05 -
Reaction Forces
01:49
BONUS Project / Real Model Creation
-
Exporting The Variables And Defining The Main Sketch Again
03:55 -
The Main Frames and The Main Connection
09:26 -
Patterning The Other Joint
02:14 -
Creating Supports Plates
08:20 -
Placing Supports
06:06 -
End Caps and Column Base Plate
06:22 -
Purlins Plates
03:35 -
Purlins Placing
04:43 -
Rod Placing
07:35
BONUS Project / Detailing
-
General Info About the Detailing
02:16 -
Plates Naming Part 1
05:16 -
Plates Naming Part 2
03:04 -
Naming the Remaining Elements
01:31 -
Creating The General Drawing
03:52 -
Column Detailing
04:10 -
Pipes 1A & 2A Detailing
05:35 -
Supports Detailing
05:12 -
Pipe Cutting Pattern
08:09 -
Purlin Detailing
08:01 -
Column Assembly Part 1
07:05 -
Column Assembly Part 2
06:31 -
Column Assembly Part 3
04:01 -
Pipe Assembly Part 1
04:43 -
Pipe Assembly Part 2
06:59 -
Exporting DWG Cutting Files 1
06:38 -
Exporting DWG Cutting Files 2
04:32 -
Exporting DWG Cutting Files 3
07:56